Brake Anti Rattle Clip Installation
Save on Dorman - Help Disc Brake Anti-Rattle Clip Assortment 26210 at Advance Auto Parts. Buy online, pick up in-store in 30 minutes.
Anti Rattle Spring Products Disc brake systems have an Anti Rattle Spring in order to minimize the noise caused by contact between the brakes' friction element and the brake caliper or the piston cup. When this spring is damaged or comes off, you'll need to replace it immediately to keep your brakes working without a fuss and to prevent unnecessary wear on your braking system components.
4k Camera: 6. Mini Microphone: 7. My computer for editing / uploading: 8.
Thanks in advance!
Reconnect the ABS sensor wire, if you have removed one. Replace the wheels on the axle hubs. Install the lug nuts on the rim and tighten them only snug with the tire iron. Refer to your owner's service manual for the correct foot-pound torque for your wheels, and tighten them with a torque wrench.
The outer pads had the longer sized clips with the tabs facing outward. I took a picture of the outer pad, does it look right? I fooled around installing the short ones here also and quite honestly, it too, looks 'right', so please answer only if you are sure that what is shown is the correct install. I installed them like the existing, but the wife complained about a great deal of brake noise before I changed them, so I'm not sure they were installed correctly previously. Second question, are all four pads identical? Seems like you'd want to have a different ridge type on the outer pads to mate with the caliper body than on the inside that mates with the piston. They were identical in the pad I removed, but forgot to check on the installed ones.
PROPER PAD BED- DING CAN PREVENT ROTOR WARPING. 5 moderate to aggressive stops from 40 mph down to 10 mph in rapid succession without letting the brakes cool and do not come to a complete stop. If you're forced to stop, either shift into neutral or give room in front so you can allow the vehicle to roll slightly while waiting for the light. The rotors will be very hot and holding down the brake pedal will allow the pad to create an imprint on the rotor. This is where the judder can originate from. Then do 5 moderate stops from 35 mph to 5 mph in rapid succession without letting the brakes cool. You should expect to smell some resin as the brakes get hot.
Image: Also, you can see that I slightly bent the ears on the anti-rattle clip, was this proper? I can undo it if necessary, still haven't done it to the other side.
The finished product: Good luck!! Quote, originally posted by wannabemechanic » I hear that clunking in mine too whenever I'm in reverse. Usually when I'm backing up and I have the steering wheel turned to the right. Sounds like the CV Joint I think it's called? The boot thing near the wheel, but as you know I just had it in the shop and they didn't say anything about replacing those. I'm taking it to the shop in the morning so I'll ask about that and if the clips will help mine.
However, don't use petroleum based lubricants. It can come off the slides and get on the dust boots of the calipers. This will deteriorate the boots. A very good product designed to use for this is Sil-Glyde. Its silicone based. You can get it at NAPA.
Brake Pad Anti Rattle Clip
If you think brake pad rattle is not a big issue, think again because it may lead to the premature wear of your braking components if unresolved. The good news is that anti-rattle spring installation just requires at least 30 minutes of your time. Line up the tools, follow the steps, and expect a quieter ride after this task.
Brake Anti Rattle Clip Installation
The tangs on the clips will hold the pads in place. Release the bungee cord and set the caliper back down over the rotor. Note: if shim plates came with the pads, reinstall them behind the brake disc pads in the same position.
Some suppliers may not also include this product under a return policy. However, you may prolong the life of your clips by applying grease on them once you replace them together with your brake pads. One sign that something is improperly installed in your car is rattle or vibration of small parts. In a braking system, this noise may be present if the anti-rattle spring in your front brakes is not fitted securely. Wacom cintiq 22hd touch tablet. This spring or clip prevents the brake pads on the brake disc from vibrating or chattering; the brake pads (especially when slightly worn) must be held in place by this clip.
Make sure that the holes on the pads' metal backing contact with the loops on the clip. The clip has a spring-loaded design that will hold the pads against the housing.
Brake Caliper Clips Installation
Mechanic’s Tool Set: 3. Disposable Gloves: 4. Common Sense 5.